/*************************************************************************
* Arduino GPS/OBD-II/G-Force Data Logger
* Distributed under GPL v2.0
* Copyright (c) 2013 Stanley Huang <stanleyhuangyc@gmail.com>
* All rights reserved.
*************************************************************************/

#include <Arduino.h>
#include <Wire.h>
#include <OBD.h>
#include <SPI.h>
#include <SD.h>
#include <MPU6050.h>
#include "MultiLCD.h"
#include "images.h"
#include "config.h"
#if USE_SOFTSERIAL
#include <SoftwareSerial.h>
#endif
#include "datalogger.h"

// logger states
#define STATE_SD_READY 0x1
#define STATE_OBD_READY 0x2
#define STATE_GPS_FOUND 0x4
#define STATE_GPS_READY 0x8
#define STATE_ACC_READY 0x10
#define STATE_SLEEPING 0x20

static uint32_t lastFileSize = 0;
static int lastSpeed = -1;
static int speed = 0;
static uint32_t distance = 0;
static uint16_t fileIndex = 0;
static uint32_t startTime = 0;
static uint8_t lastPid = 0;
static int lastValue = 0;

static byte pidTier1[]= {PID_RPM, PID_SPEED, PID_ENGINE_LOAD, PID_THROTTLE};
static byte pidTier2[] = {PID_INTAKE_MAP, PID_TIMING_ADVANCE};
static byte pidTier3[] = {PID_COOLANT_TEMP, PID_INTAKE_TEMP, PID_AMBIENT_TEMP, PID_FUEL_LEVEL, PID_DISTANCE};

#define TIER_NUM1 sizeof(pidTier1)
#define TIER_NUM2 sizeof(pidTier2)
#define TIER_NUM3 sizeof(pidTier3)

class COBDLogger : public COBD, public CDataLogger
{
public:
    COBDLogger():state(0) {}
    void setup()
    {
        showStates();

#if USE_MPU6050
        Wire.begin();
        if (MPU6050_init() == 0) {
            state |= STATE_ACC_READY;
            showStates();
        }
#endif

        do {
            showStates();
        } while (!init());

        state |= STATE_OBD_READY;

        showStates();

        uint16_t flags = FLAG_CAR | FLAG_OBD;
        if (state & STATE_GPS_FOUND) flags |= FLAG_GPS;
        if (state & STATE_ACC_READY) flags |= FLAG_ACC;
#if ENABLE_DATA_LOG
        uint16_t index = openFile(LOG_TYPE_DEFAULT, flags);
        lcd.setFont(FONT_SIZE_SMALL);
        lcd.setCursor(86, 0);
        if (index) {
            lcd.write('[');
            lcd.setFlags(FLAG_PAD_ZERO);
            lcd.printInt(index, 5);
            lcd.setFlags(0);
            lcd.write(']');
        } else {
            lcd.print("NO LOG");
        }
        delay(100);
#endif

        //showECUCap();
        //delay(3000);

#if ENABLE_DATA_LOG
        // open file for logging
        if (!(state & STATE_SD_READY)) {
            if (checkSD()) {
                state |= STATE_SD_READY;
                showStates();
            }
        }
#endif

        initScreen();
    }
    void loop()
    {
        static byte index = 0;
        static byte index2 = 0;
        static byte index3 = 0;
        uint32_t t = millis();

        logOBDData(pidTier1[index++]);
        if (index == TIER_NUM1) {
            index = 0;
            if (index2 == TIER_NUM2) {
                index2 = 0;
                logOBDData(pidTier3[index3]);
                index3 = (index3 + 1) % TIER_NUM3;
            } else {
                logOBDData(pidTier2[index2++]);
            }
        }


#if USE_MPU6050
        if (state & STATE_ACC_READY) {
            processAccelerometer();
        }
#endif

#if ENABLE_DATA_LOG
        // flush SD data every 1KB
        if (dataSize - lastFileSize >= 1024) {
            flushFile();
            lastFileSize = dataSize;
            // display logged data size
            lcd.setFont(FONT_SIZE_MEDIUM);
            lcd.setCursor(248, 11);
            lcd.printInt(dataSize >> 10);
            lcd.print("KB");
        }
#endif

        if (errors >= 2) {
            reconnect();
        }
    }
#if ENABLE_DATA_LOG
    bool checkSD()
    {
        Sd2Card card;
        SdVolume volume;
        state &= ~STATE_SD_READY;
        pinMode(SS, OUTPUT);
        if (card.init(SPI_FULL_SPEED, SD_CS_PIN)) {
            const char* type;

            lcd.print("SD");
            switch(card.type()) {
            case SD_CARD_TYPE_SD1:
                type = "1";
                break;
            case SD_CARD_TYPE_SD2:
                type = "2";
                break;
            case SD_CARD_TYPE_SDHC:
                type = "HC";
                break;
            default:
                type = "x";
            }

            lcd.print(type);
            lcd.write(' ');
            if (!volume.init(card)) {
                lcd.print("No FAT");
                return false;
            }

            uint32_t volumesize = volume.blocksPerCluster();
            volumesize >>= 1; // 512 bytes per block
            volumesize *= volume.clusterCount();
            volumesize >>= 10;

            lcd.print((int)((volumesize + 511) / 1000));
            lcd.print("GB");
        } else {
            lcd.print("SD  ");
            lcd.draw(cross, 16, 16);
            return false;
        }

        if (!SD.begin(SD_CS_PIN)) {
            lcd.print("Bad");
            return false;
        }

        state |= STATE_SD_READY;
        return true;
    }
#endif
    void initScreen()
    {
        initLoggerScreen();
    }
private:
    void dataIdleLoop()
    {
        if (lastPid) {
            showData(lastPid, lastValue);
            lastPid = 0;
        }
    }
#if USE_MPU6050
    void processAccelerometer()
    {
        accel_t_gyro_union data;
        MPU6050_readout(&data);
        dataTime = millis();
        // log x/y/z of accelerometer
        logData(PID_ACC, data.value.x_accel, data.value.y_accel, data.value.z_accel);
        //showGForce(data.value.y_accel);
        // log x/y/z of gyro meter
        logData(PID_GYRO, data.value.x_gyro, data.value.y_gyro, data.value.z_gyro);
    }
#endif
    void logOBDData(byte pid)
    {
        int value;
        // send a query to OBD adapter for specified OBD-II pid
        if (read(pid, value)) {
            dataTime = millis();
            // log data to SD card
            logData(0x100 | pid, value);
            lastValue = value;
            lastPid = pid;
        }
    }
    void showECUCap()
    {
        byte pidlist[] = {PID_RPM, PID_SPEED, PID_THROTTLE, PID_ENGINE_LOAD, PID_CONTROL_MODULE_VOLTAGE, PID_MAF_FLOW, PID_INTAKE_MAP, PID_FUEL_LEVEL, PID_FUEL_PRESSURE, PID_COOLANT_TEMP, PID_INTAKE_TEMP, PID_AMBIENT_TEMP, PID_TIMING_ADVANCE, PID_BAROMETRIC};
        const char* namelist[] = {"RPM", "SPEED", "THR", "ENG.LOAD", "CTRL VOLT", "MAF", "MAP", "FUEL LV.", "FUEL PRE.", "COOLANT", "INTAKE","AMBIENT", "IGNITION", "BARO"};
        lcd.setFont(FONT_SIZE_MEDIUM);
        for (byte i = 0; i < sizeof(pidlist) / sizeof(pidlist[0]); i++) {
            lcd.setCursor(192, i << 1);
            lcd.print(namelist[i]);
            lcd.write(':');
            showTickCross(isValidPID(pidlist[i]));
        }
    }
    void reconnect()
    {
#if ENABLE_DATA_LOG
        closeFile();
#endif
        lcd.clear();
        lcd.setFont(FONT_SIZE_MEDIUM);
        lcd.print("Reconnecting");
        startTime = millis();
        state &= ~(STATE_OBD_READY | STATE_ACC_READY);
        state |= STATE_SLEEPING;
        //digitalWrite(SD_CS_PIN, LOW);
        for (int i = 0; !init(); i++) {
            if (i == 10) lcd.clear();
        }
        state &= ~STATE_SLEEPING;
        fileIndex++;
        write('\r');
        setup();
    }
    byte state;

    void showTickCross(bool yes)
    {
        lcd.setTextColor(yes ? RGB16_GREEN : RGB16_RED);
        lcd.draw(yes ? tick : cross, 16, 16);
        lcd.setTextColor(RGB16_WHITE);
    }
    // screen layout related stuff
    void showStates()
    {
        lcd.setFont(FONT_SIZE_MEDIUM);
        lcd.setCursor(0, 10);
        lcd.print("OBD ");
        showTickCross(state & STATE_OBD_READY);
        lcd.setCursor(0, 13);
        lcd.print("ACC ");
        showTickCross(state & STATE_ACC_READY);
    }
#if USE_MPU6050
    void showGForce(int g)
    {
        byte n;
        /* 0~1.5g -> 0~8 */
        g /= 85 * 25;
        lcd.setFont(FONT_SIZE_SMALL);
        lcd.setCursor(0, 3);
        if (g == 0) {
            lcd.clearLine(1);
        } else if (g < 0 && g >= -10) {
            for (n = 0; n < 10 + g; n++) {
                lcd.write(' ');
            }
            for (; n < 10; n++) {
                lcd.write('<');
            }
            lcd.print("        ");
        } else if (g > 0 && g < 10) {
            lcd.print("        ");
            for (n = 0; n < g; n++) {
                lcd.write('>');
            }
            for (; n < 10; n++) {
                lcd.write(' ');
            }
        }
    }
#endif
    void showData(byte pid, int value)
    {
        switch (pid) {
        case PID_RPM:
            lcd.setCursor(0, 2);
            lcd.setFont(FONT_SIZE_XLARGE);
            lcd.printInt((unsigned int)value % 10000, 4);
            showChart(value);
            break;
        case PID_SPEED:
            if (lastSpeed != value) {
                lcd.setCursor(90, 2);
                lcd.setFont(FONT_SIZE_XLARGE);
                lcd.printInt((unsigned int)value % 1000, 3);
                lastSpeed = value;
            }
            break;
        case PID_ENGINE_LOAD:
            lcd.setCursor(164, 2);
            lcd.setFont(FONT_SIZE_XLARGE);
            lcd.printInt(value % 100, 3);
            break;
        case PID_INTAKE_TEMP:
            if ((uint16_t)value < 1000) {
                lcd.setCursor(248, 2);
                lcd.setFont(FONT_SIZE_XLARGE);
                lcd.printInt(value, 3);
            }
            break;
        case PID_INTAKE_MAP:
            lcd.setCursor(164, 9);
            lcd.setFont(FONT_SIZE_XLARGE);
            lcd.printInt((uint16_t)value % 1000, 3);
            break;
        case PID_COOLANT_TEMP:
            lcd.setCursor(8, 9);
            lcd.setFont(FONT_SIZE_XLARGE);
            lcd.printInt((uint16_t)value % 1000, 3);
            break;
        case PID_DISTANCE:
            lcd.setFont(FONT_SIZE_XLARGE);
            lcd.setCursor(90, 9);
            lcd.printInt((uint16_t)value % 1000, 3);
            break;
        }
    }
    void showChart(int value)
    {
        static uint16_t pos = 0;
        byte n = value / 60;
        lcd.fill(pos, pos, 239 - n, 239, RGB16_CYAN);
        if (++pos == 320) {
            lcd.fill(0, 319, 120, 239);
            pos = 0;
        }
    }
    void initLoggerScreen()
    {
        lcd.clear();
        lcd.backlight(true);
        lcd.setFont(FONT_SIZE_SMALL);
        lcd.setTextColor(RGB16_CYAN);
        lcd.setCursor(4, 0);
        lcd.print("ENGINE RPM");
        lcd.setCursor(104, 0);
        lcd.print("SPEED");
        lcd.setCursor(164, 0);
        lcd.print("ENGINE LOAD");
        lcd.setCursor(248, 0);
        lcd.print("INTAKE TEMP");

        lcd.setCursor(4, 7);
        lcd.print("COOLANT TEMP");
        lcd.setCursor(104, 7);
        lcd.print("DISTANCE");
        lcd.setCursor(164, 7);
        lcd.print("INTAKE MAP");

        lcd.setCursor(248, 7);
        lcd.print("OBD Time:");
        lcd.setCursor(248, 10);
        lcd.print("Log Size:");

        lcd.setTextColor(RGB16_YELLOW);
        lcd.setCursor(24, 5);
        lcd.print("rpm");
        lcd.setCursor(110, 5);
        lcd.print("km/h");
        lcd.setCursor(216, 4);
        lcd.print("%");
        lcd.setCursor(304, 4);
        lcd.print("C");
        lcd.setCursor(64, 11);
        lcd.print("C");
        lcd.setCursor(110, 12);
        lcd.print("km");
        lcd.setCursor(200, 12);
        lcd.print("kpa");

        lcd.setTextColor(RGB16_WHITE);


        //lcd.setCursor(0, 5);
        //lcd.print("THR:   %");
        //lcd.setCursor(80, 5);
        //lcd.print("AIR:   C");
    }
};

static COBDLogger logger;

void setup()
{
    lcd.begin();
    lcd.setFont(FONT_SIZE_MEDIUM);
    lcd.setTextColor(RGB16_YELLOW);
    lcd.println("UnoLogger");
    lcd.setTextColor(RGB16_WHITE);

    logger.begin();
    logger.initSender();

#if ENABLE_DATA_LOG
    lcd.setFont(FONT_SIZE_MEDIUM);
    lcd.setCursor(0, 7);
    logger.checkSD();
#endif
    logger.setup();
}

void loop()
{
    logger.loop();
}