summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--tester/config.h43
-rw-r--r--tester/datalogger.h250
-rw-r--r--tester/tester.ino485
3 files changed, 778 insertions, 0 deletions
diff --git a/tester/config.h b/tester/config.h
new file mode 100644
index 0000000..f8ff4f5
--- /dev/null
+++ b/tester/config.h
@@ -0,0 +1,43 @@
+#ifndef CONFIG_H_INCLUDED
+#define CONFIG_H_INCLUDED
+
+/**************************************
+* Choose model of OBD-II Adapter
+**************************************/
+// OBD_MODEL_I2C for I2C version
+// OBD_MODEL_UART for UART version
+#define OBD_MODEL OBD_MODEL_I2C
+#define OBD_PROTOCOL PROTO_AUTO
+
+/**************************************
+* Accelerometer & Gyro
+**************************************/
+//#define USE_MPU6050 1
+#define USE_MPU9150 1
+
+/**************************************
+* LCD module (uncomment only one)
+**************************************/
+LCD_ILI9341 lcd; /* 2.4" ILI9341 based SPI TFT LCD */
+//LCD_Null lcd;
+
+/**************************************
+* Data streaming options
+**************************************/
+// enable(1)/disable(0) data streaming
+#define ENABLE_DATA_OUT 1
+
+// uses software(1)/hardware(0) serial for data streaming
+#define USE_SOFTSERIAL 0
+
+// followings define the format of data streaming, enable one of them only
+// FORMAT_BIN is required by Freematics OBD iOS App
+//#define STREAM_FORMAT FORMAT_BIN
+// FORMAT_CSV is for CSV based text output
+//#define STREAM_FORMAT FORMAT_CSV
+// FORMAT_LINE is for readable text output
+#define STREAM_FORMAT FORMAT_TEXT
+
+#define STREAM_BAUDRATE 115200
+
+#endif
diff --git a/tester/datalogger.h b/tester/datalogger.h
new file mode 100644
index 0000000..241d3cf
--- /dev/null
+++ b/tester/datalogger.h
@@ -0,0 +1,250 @@
+#define FORMAT_BIN 0
+#define FORMAT_CSV 1
+#define FORMAT_TEXT 2
+
+typedef struct {
+ uint32_t time;
+ uint16_t pid;
+ uint8_t flags;
+ uint8_t checksum;
+ float value[3];
+} LOG_DATA_COMM;
+
+#define PID_GPS_LATITUDE 0xA
+#define PID_GPS_LONGITUDE 0xB
+#define PID_GPS_ALTITUDE 0xC
+#define PID_GPS_SPEED 0xD
+#define PID_GPS_HEADING 0xE
+#define PID_GPS_SAT_COUNT 0xF
+#define PID_GPS_TIME 0x10
+#define PID_GPS_DATE 0x11
+
+#define PID_ACC 0x20
+#define PID_GYRO 0x21
+#define PID_COMPASS 0x22
+#define PID_MEMS_TEMP 0x23
+#define PID_BATTERY_VOLTAGE 0x24
+
+#define PID_DATA_SIZE 0x80
+
+#define FILE_NAME_FORMAT "/DAT%05d.CSV"
+
+#if ENABLE_DATA_OUT
+
+#if USE_SOFTSERIAL
+SoftwareSerial SerialRF(A2, A3);
+#else
+#define SerialRF Serial
+#endif
+
+#endif
+
+#if ENABLE_DATA_LOG
+static File sdfile;
+#endif
+
+typedef struct {
+ uint16_t pid;
+ char name[3];
+} PID_NAME;
+
+const PID_NAME pidNames[] PROGMEM = {
+{PID_ACC, {'A','C','C'}},
+{PID_GYRO, {'G','Y','R'}},
+{PID_COMPASS, {'M','A','G'}},
+{PID_GPS_LATITUDE, {'L','A','T'}},
+{PID_GPS_LONGITUDE, {'L','O','N'}},
+{PID_GPS_ALTITUDE, {'A','L','T'}},
+{PID_GPS_SPEED, {'S','P','D'}},
+{PID_GPS_HEADING, {'C','R','S'}},
+{PID_GPS_SAT_COUNT, {'S','A','T'}},
+{PID_GPS_TIME, {'T','M','E'}},
+{PID_GPS_DATE, {'D','T','E'}},
+{PID_BATTERY_VOLTAGE, {'B','A','T'}},
+{PID_DATA_SIZE, {'D','A','T'}},
+};
+
+class CDataLogger {
+public:
+ void initSender()
+ {
+#if ENABLE_DATA_OUT
+ SerialRF.begin(STREAM_BAUDRATE);
+#endif
+#if ENABLE_DATA_LOG
+ m_lastDataTime = 0;
+#endif
+ }
+ void recordData(const char* buf)
+ {
+#if ENABLE_DATA_LOG
+ dataSize += sdfile.print(dataTime - m_lastDataTime);
+ dataSize += sdfile.write(',');
+ dataSize += sdfile.write(buf);
+ m_lastDataTime = dataTime;
+#endif
+ }
+ void logData(char c)
+ {
+#if ENABLE_DATA_LOG
+ if (c >= ' ') {
+ sdfile.write(c);
+ dataSize++;
+ }
+#endif
+ }
+ void logData(uint16_t pid, int value)
+ {
+ char buf[16];
+#if STREAM_FORMAT == FORMAT_TEXT
+ sprintf(buf + translatePIDName(pid, buf), "%d\r", value);
+#else
+ sprintf(buf, "%X,%d\r", pid, value);
+#endif
+#if ENABLE_DATA_OUT
+#if STREAM_FORMAT == FORMAT_BIN
+ LOG_DATA_COMM ld = {dataTime, pid, 1, 0, value};
+ ld.checksum = getChecksum((char*)&ld, 12);
+ SerialRF.write((uint8_t*)&ld, 12);
+#else
+ SerialRF.print(buf);
+#endif
+#ifdef DELAY_AFTER_SENDING
+ delay(DELAY_AFTER_SENDING);
+#endif
+#endif
+ recordData(buf);
+ }
+ void logData(uint16_t pid, int32_t value)
+ {
+ char buf[20];
+#if STREAM_FORMAT == FORMAT_TEXT
+ sprintf(buf + translatePIDName(pid, buf), "%ld\r", value);
+#else
+ sprintf(buf, "%X,%ld\r", pid, value);
+#endif
+#if ENABLE_DATA_OUT
+#if STREAM_FORMAT == FORMAT_BIN
+ LOG_DATA_COMM ld = {dataTime, pid, 1, 0, value};
+ ld.checksum = getChecksum((char*)&ld, 12);
+ SerialRF.write((uint8_t*)&ld, 12);
+#else
+ SerialRF.print(buf);
+#endif
+#ifdef DELAY_AFTER_SENDING
+ delay(DELAY_AFTER_SENDING);
+#endif
+#endif
+ recordData(buf);
+ }
+ void logData(uint16_t pid, uint32_t value)
+ {
+ char buf[20];
+#if STREAM_FORMAT == FORMAT_TEXT
+ sprintf(buf + translatePIDName(pid, buf), "%lu\r", value);
+#else
+ sprintf(buf, "%X,%lu\r", pid, value);
+#endif
+#if ENABLE_DATA_OUT
+#if STREAM_FORMAT == FORMAT_BIN
+ LOG_DATA_COMM ld = {dataTime, pid, 1, 0, value};
+ ld.checksum = getChecksum((char*)&ld, 12);
+ SerialRF.write((uint8_t*)&ld, 12);
+#else
+ SerialRF.print(buf);
+#endif
+#endif
+#ifdef DELAY_AFTER_SENDING
+ delay(DELAY_AFTER_SENDING);
+#endif
+ recordData(buf);
+ }
+ void logData(uint16_t pid, int value1, int value2, int value3)
+ {
+ char buf[24];
+#if STREAM_FORMAT == FORMAT_TEXT
+ sprintf(buf + translatePIDName(pid, buf), "%d,%d,%d\r", value1, value2, value3);
+#else
+ sprintf(buf, "%X,%d,%d,%d\r", pid, value1, value2, value3);
+#endif
+#if ENABLE_DATA_OUT
+#if STREAM_FORMAT == FORMAT_BIN
+ LOG_DATA_COMM ld = {dataTime, pid, 3, 0, {value1, value2, value3}};
+ ld.checksum = getChecksum((char*)&ld, 20);
+ SerialRF.write((uint8_t*)&ld, 20);
+#else
+ SerialRF.print(buf);
+#endif
+#ifdef DELAY_AFTER_SENDING
+ delay(DELAY_AFTER_SENDING);
+#endif
+#endif
+ recordData(buf);
+ }
+#if ENABLE_DATA_LOG
+ uint16_t openFile(uint16_t logFlags = 0, uint32_t dateTime = 0)
+ {
+ uint16_t fileIndex;
+ char filename[24] = "/FRMATICS";
+
+ dataSize = 0;
+ if (SD.exists(filename)) {
+ for (fileIndex = 1; fileIndex; fileIndex++) {
+ sprintf(filename + 9, FILE_NAME_FORMAT, fileIndex);
+ if (!SD.exists(filename)) {
+ break;
+ }
+ }
+ if (fileIndex == 0)
+ return 0;
+ } else {
+ SD.mkdir(filename);
+ fileIndex = 1;
+ sprintf(filename + 9, FILE_NAME_FORMAT, 1);
+ }
+
+ sdfile = SD.open(filename, FILE_WRITE);
+ if (!sdfile) {
+ return 0;
+ }
+ m_lastDataTime = dateTime;
+ return fileIndex;
+ }
+ void closeFile()
+ {
+ sdfile.close();
+ }
+ void flushFile()
+ {
+ sdfile.flush();
+ }
+#endif
+ uint32_t dataTime;
+ uint32_t dataSize;
+private:
+ byte getChecksum(char* buffer, byte len)
+ {
+ uint8_t checksum = 0;
+ for (byte i = 0; i < len; i++) {
+ checksum ^= buffer[i];
+ }
+ return checksum;
+ }
+#if STREAM_FORMAT == FORMAT_TEXT
+ byte translatePIDName(uint16_t pid, char* text)
+ {
+ for (uint16_t n = 0; n < sizeof(pidNames) / sizeof(pidNames[0]); n++) {
+ uint16_t id = pgm_read_word(&pidNames[n].pid);
+ if (pid == id) {
+ memcpy_P(text, pidNames[n].name, 3);
+ text[3] = '=';
+ return 4;
+ }
+ }
+ return sprintf(text, "%X=", pid);
+ }
+#endif
+#if ENABLE_DATA_LOG
+ uint32_t m_lastDataTime;
+#endif
+};
diff --git a/tester/tester.ino b/tester/tester.ino
new file mode 100644
index 0000000..828e83f
--- /dev/null
+++ b/tester/tester.ino
@@ -0,0 +1,485 @@
+/*************************************************************************
+* Tester sketch for Freematics OBD-II Adapter for Arduino
+* Distributed under GPL v2.0
+* Written by Stanley Huang <stanleyhuangyc@gmail.com>
+* Visit freematics.com for product information
+*************************************************************************/
+
+#include <Arduino.h>
+#include <OBD.h>
+#include <SPI.h>
+#include <Wire.h>
+#include <I2Cdev.h>
+#include <MPU9150.h>
+#include "MultiLCD.h"
+#include "config.h"
+#include "datalogger.h"
+
+#define OBD_MODEL_UART 0
+#define OBD_MODEL_I2C 1
+
+#define STATE_MEMS_READY 1
+#define STATE_INIT_DONE 2
+
+void(* resetFunc) (void) = 0; //declare reset function at address 0
+
+static uint32_t lastFileSize = 0;
+static int speed = 0;
+static uint32_t distance = 0;
+static uint16_t fileIndex = 0;
+static uint32_t startTime = 0;
+static uint16_t elapsed = 0;
+static uint8_t lastPid = 0;
+static int lastValue = 0;
+
+#if USE_MPU6050 || USE_MPU9150
+MPU6050 accelgyro;
+#endif
+
+static const PROGMEM uint8_t tick[16 * 16 / 8] =
+{0x00,0x80,0xC0,0xE0,0xC0,0x80,0x00,0x80,0xC0,0xE0,0xF0,0xF8,0xFC,0x78,0x30,0x00,0x00,0x01,0x03,0x07,0x0F,0x1F,0x1F,0x1F,0x0F,0x07,0x03,0x01,0x00,0x00,0x00,0x00};
+
+static const byte PROGMEM pidTier1[]= {PID_RPM, PID_SPEED, PID_ENGINE_LOAD, PID_THROTTLE};
+static const byte PROGMEM pidTier2[] = {PID_INTAKE_MAP, PID_MAF_FLOW, PID_TIMING_ADVANCE};
+static const byte PROGMEM pidTier3[] = {PID_COOLANT_TEMP, PID_INTAKE_TEMP, PID_AMBIENT_TEMP, PID_ENGINE_FUEL_RATE, PID_DISTANCE};
+
+#define TIER_NUM1 sizeof(pidTier1)
+#define TIER_NUM2 sizeof(pidTier2)
+#define TIER_NUM3 sizeof(pidTier3)
+
+#if OBD_MODEL == OBD_MODEL_UART
+class COBDDevice : public COBD, public CDataLogger
+#else
+class COBDDevice : public COBDI2C, public CDataLogger
+#endif
+{
+public:
+ COBDDevice():state(0) {}
+ void setup()
+ {
+#if USE_MPU6050 || USE_MPU9150
+ Wire.begin();
+ accelgyro.initialize();
+ if (accelgyro.testConnection()) state |= STATE_MEMS_READY;
+#endif
+
+ testOut();
+
+ while (!init(OBD_PROTOCOL));
+
+ showVIN();
+
+ showECUCap();
+ delay(3000);
+
+ benchmark();
+ delay(5000);
+
+ initScreen();
+
+ state |= STATE_INIT_DONE;
+ }
+ void testOut()
+ {
+ static const char PROGMEM cmds[][6] = {"ATZ\r", "ATL1\r", "ATRV\r", "0100\r", "010C\r", "010D\r", "0902\r"};
+ char buf[OBD_RECV_BUF_SIZE];
+
+ lcd.setColor(RGB16_WHITE);
+ lcd.setFontSize(FONT_SIZE_SMALL);
+ lcd.setCursor(0, 4);
+
+ // recover from possible previous incomplete communication
+ recover();
+ for (byte i = 0; i < sizeof(cmds) / sizeof(cmds[0]); i++) {
+ char cmd[6];
+ memcpy_P(cmd, cmds[i], sizeof(cmd));
+ lcd.setColor(RGB16_WHITE);
+ lcd.print("Sending ");
+ lcd.println(cmd);
+ lcd.setColor(RGB16_CYAN);
+ if (sendCommand(cmd, buf)) {
+ char *p = strstr(buf, cmd);
+ if (p)
+ p += strlen(cmd);
+ else
+ p = buf;
+ while (*p == '\r') p++;
+ while (*p) {
+ lcd.write(*p);
+ if (*p == '\r' && *(p + 1) != '\r')
+ lcd.write('\n');
+ p++;
+ }
+ } else {
+ lcd.println("Timeout");
+ }
+ delay(1000);
+ }
+ }
+ void showVIN()
+ {
+ char buf[OBD_RECV_BUF_SIZE];
+ lcd.setFontSize(FONT_SIZE_MEDIUM);
+ if (getVIN(buf)) {
+ lcd.setColor(RGB16_WHITE);
+ lcd.print("\nVIN:");
+ lcd.setColor(RGB16_YELLOW);
+ lcd.println(buf);
+ } else {
+ lcd.println("error");
+ }
+ }
+ void showECUCap()
+ {
+ static const byte PROGMEM pidlist[] = {PID_ENGINE_LOAD, PID_COOLANT_TEMP, PID_FUEL_PRESSURE, PID_INTAKE_MAP, PID_RPM, PID_SPEED, PID_TIMING_ADVANCE, PID_INTAKE_TEMP, PID_MAF_FLOW, PID_THROTTLE, PID_AUX_INPUT,
+ PID_EGR_ERROR, PID_COMMANDED_EVAPORATIVE_PURGE, PID_FUEL_LEVEL, PID_CONTROL_MODULE_VOLTAGE, PID_ABSOLUTE_ENGINE_LOAD, PID_AMBIENT_TEMP, PID_COMMANDED_THROTTLE_ACTUATOR, PID_ETHANOL_FUEL,
+ PID_FUEL_RAIL_PRESSURE, PID_HYBRID_BATTERY_PERCENTAGE, PID_ENGINE_OIL_TEMP, PID_FUEL_INJECTION_TIMING, PID_ENGINE_FUEL_RATE, PID_ENGINE_TORQUE_DEMANDED, PID_ENGINE_TORQUE_PERCENTAGE};
+
+ lcd.setColor(RGB16_WHITE);
+ lcd.setFontSize(FONT_SIZE_MEDIUM);
+ for (byte i = 0; i < sizeof(pidlist) / sizeof(pidlist[0]); i += 2) {
+ for (byte j = 0; j < 2; j++) {
+ byte pid = pgm_read_byte(pidlist + i + j);
+ lcd.setCursor(216 + j * 56 , i + 4);
+ lcd.print((int)pid | 0x100, HEX);
+ bool valid = isValidPID(pid);
+ if (valid) {
+ lcd.setColor(RGB16_GREEN);
+ lcd.draw(tick, 16, 16);
+ lcd.setColor(RGB16_WHITE);
+ }
+ }
+ }
+ }
+ void benchmark()
+ {
+ lcd.clear();
+ lcd.setFontSize(FONT_SIZE_MEDIUM);
+ lcd.setColor(RGB16_YELLOW);
+ lcd.println("Benchmarking OBD-II...");
+ lcd.setColor(RGB16_WHITE);
+ lcd.setFontSize(FONT_SIZE_SMALL);
+
+ uint32_t elapsed;
+ char buf[OBD_RECV_BUF_SIZE];
+ uint16_t count = 0;
+ for (elapsed = 0; elapsed < 10000; ) {
+ lcd.setCursor(0, 4);
+ for (byte n = 0; n < TIER_NUM1; n++) {
+ byte pid = pgm_read_byte(pidTier1 + n);
+ char cmd[6];
+ sprintf(cmd, "01%02X\r", pid);
+ lcd.setColor(RGB16_CYAN);
+ lcd.print('[');
+ lcd.print(elapsed);
+ lcd.print("] ");
+ lcd.setColor(RGB16_WHITE);
+ lcd.println(cmd);
+ startTime = millis();
+ if (sendCommand(cmd, buf)) {
+ elapsed += (millis() - startTime);
+ count++;
+ lcd.setColor(RGB16_GREEN);
+ lcd.println(buf);
+ } else {
+ lcd.setColor(RGB16_RED);
+ lcd.println("Timeout!");
+ }
+ }
+ }
+ lcd.setFontSize(FONT_SIZE_MEDIUM);
+ lcd.setColor(RGB16_WHITE);
+ if (count) {
+ lcd.print("\nOBD-II PID Access Time: ");
+ lcd.print(elapsed / count);
+ lcd.println("ms");
+ } else {
+ lcd.println("\nNo Data!");
+ }
+
+#if USE_MPU6050 || USE_MPU9150
+ if (!(state & STATE_MEMS_READY)) return;
+ lcd.setColor(RGB16_YELLOW);
+ lcd.println("\nBenchmarking MEMS...");
+ startTime = millis();
+ for (count = 0, elapsed = 0; elapsed < 3000; elapsed = millis() - startTime, count++) {
+ int16_t ax, ay, az;
+ int16_t gx, gy, gz;
+#if USE_MPU9150
+ int16_t mx, my, mz;
+ accelgyro.getMotion9(&ax, &ay, &az, &gx, &gy, &gz, &mx, &my, &mz);
+#else
+ accelgyro.getMotion6(&ax, &ay, &az, &gx, &gy, &gz);
+#endif
+ }
+ lcd.setColor(RGB16_WHITE);
+ lcd.println();
+#if USE_MPU9150
+ lcd.print('9');
+#else
+ lcd.print('6');
+#endif
+ lcd.print("-Axis Data Access Time: ");
+ lcd.print(elapsed / count);
+ lcd.println("ms");
+#endif
+ }
+ void logOBDData(byte pid)
+ {
+ int value;
+ if (read(pid, value)) {
+ logData(pid, value);
+ showData(pid, value);
+ }
+ }
+ void loop()
+ {
+ static byte index = 0;
+ static byte index2 = 0;
+ static byte index3 = 0;
+ byte pid = pgm_read_byte(pidTier1 + index++);
+ logOBDData(pid);
+ if (index == TIER_NUM1) {
+ index = 0;
+ if (index2 == TIER_NUM2) {
+ index2 = 0;
+ pid = pgm_read_byte(pidTier3 + index3);
+ if (isValidPID(pid)) {
+ logOBDData(pid);
+ }
+ index3 = (index3 + 1) % TIER_NUM3;
+ if (index3 == 0) {
+ float v = getVoltage();
+ ShowVoltage(v);
+ }
+ } else {
+ pid = pgm_read_byte(pidTier2 + index2);
+ if (isValidPID(pid)) {
+ logOBDData(pid);
+ }
+ index2++;
+ }
+ }
+
+ if (errors >= 5) {
+ reconnect();
+ }
+ }
+#if USE_MPU6050 || USE_MPU9150
+ void logMEMSData()
+ {
+ int16_t ax, ay, az;
+ int16_t gx, gy, gz;
+#if USE_MPU9150
+ int16_t mx, my, mz;
+ accelgyro.getMotion9(&ax, &ay, &az, &gx, &gy, &gz, &mx, &my, &mz);
+#else
+ accelgyro.getMotion6(&ax, &ay, &az, &gx, &gy, &gz);
+#endif
+ dataTime = millis();
+
+ lcd.setFontSize(FONT_SIZE_SMALL);
+ lcd.setCursor(24, 14);
+ lcd.print(ax >> 4);
+ lcd.print('/');
+ lcd.print(ay >> 4);
+ lcd.print('/');
+ lcd.print(az >> 4);
+ lcd.print(' ');
+
+ lcd.setCursor(152, 14);
+ lcd.print(gx >> 4);
+ lcd.print('/');
+ lcd.print(gy >> 4);
+ lcd.print('/');
+ lcd.print(gz >> 4);
+ lcd.print(' ');
+
+#if USE_MPU9150
+ lcd.setCursor(252, 14);
+ lcd.print(mx >> 4);
+ lcd.print('/');
+ lcd.print(my >> 4);
+ lcd.print('/');
+ lcd.print(mz >> 4);
+ lcd.print(' ');
+#endif
+ lcd.setFontSize(FONT_SIZE_MEDIUM);
+
+ // log x/y/z of accelerometer
+ logData(PID_ACC, ax, ay, az);
+ // log x/y/z of gyro meter
+ logData(PID_GYRO, gx, gy, gz);
+#if USE_MPU9150
+ // log x/y/z of compass
+ logData(PID_COMPASS, mx, my, mz);
+#endif
+ }
+#endif
+ void reconnect()
+ {
+ lcd.clear();
+ lcd.setFontSize(FONT_SIZE_MEDIUM);
+ lcd.print("Reconnecting");
+ startTime = millis();
+ //digitalWrite(SD_CS_PIN, LOW);
+ for (uint16_t i = 0; ; i++) {
+ if (i == 5) {
+ lcd.setBackLight(0);
+ lcd.clear();
+ }
+ if (init()) {
+ lcd.setBackLight(255);
+ lcd.clear();
+ lcd.print("Reseting...");
+ // reset Arduino
+ resetFunc();
+ }
+ }
+ }
+ // screen layout related stuff
+ void showData(byte pid, int value)
+ {
+ switch (pid) {
+ case PID_RPM:
+ lcd.setCursor(0, 2);
+ lcd.setFontSize(FONT_SIZE_XLARGE);
+ lcd.printInt((unsigned int)value % 10000, 4);
+ showChart(value);
+ break;
+ case PID_SPEED:
+ lcd.setCursor(90, 2);
+ lcd.setFontSize(FONT_SIZE_XLARGE);
+ lcd.printInt((unsigned int)value % 1000, 3);
+ break;
+ case PID_ENGINE_LOAD:
+ lcd.setCursor(164, 2);
+ lcd.setFontSize(FONT_SIZE_XLARGE);
+ lcd.printInt(value % 100, 3);
+ break;
+ case PID_INTAKE_TEMP:
+ if (value < 0) value = 0;
+ lcd.setCursor(248, 2);
+ lcd.setFontSize(FONT_SIZE_XLARGE);
+ lcd.printInt(value, 3);
+ break;
+ case PID_INTAKE_MAP:
+ lcd.setCursor(164, 9);
+ lcd.setFontSize(FONT_SIZE_XLARGE);
+ lcd.printInt((uint16_t)value % 1000, 3);
+ break;
+ case PID_COOLANT_TEMP:
+ lcd.setCursor(8, 9);
+ lcd.setFontSize(FONT_SIZE_XLARGE);
+ lcd.printInt((uint16_t)value % 1000, 3);
+ break;
+ case PID_DISTANCE:
+ lcd.setFontSize(FONT_SIZE_XLARGE);
+ lcd.setCursor(90, 9);
+ lcd.printInt((uint16_t)value % 1000, 3);
+ break;
+ }
+ }
+ void ShowVoltage(float v)
+ {
+ lcd.setFontSize(FONT_SIZE_LARGE);
+ lcd.setCursor(260, 10);
+ lcd.setFontSize(FONT_SIZE_MEDIUM);
+ lcd.print(v);
+ }
+ void showChart(int value)
+ {
+ #define CHART_HEIGHT 100
+ static uint16_t pos = 0;
+ uint16_t height;
+ if (value >= 600) {
+ height = (value - 600) / 64;
+ if (height > CHART_HEIGHT) height = CHART_HEIGHT;
+ } else {
+ height = 1;
+ }
+ lcd.fill(pos, pos, 239 - height, 239, RGB16_CYAN);
+ pos = (pos + 1) % 320;
+ lcd.fill(pos, pos, 239 - CHART_HEIGHT, 239);
+ }
+ void initScreen()
+ {
+ lcd.clear();
+ lcd.setBackLight(255);
+ lcd.setFontSize(FONT_SIZE_SMALL);
+ lcd.setColor(RGB16_CYAN);
+ lcd.setCursor(4, 0);
+ lcd.print("ENGINE RPM");
+ lcd.setCursor(104, 0);
+ lcd.print("SPEED");
+ lcd.setCursor(164, 0);
+ lcd.print("ENGINE LOAD");
+ lcd.setCursor(248, 0);
+ lcd.print("INTAKE TEMP");
+
+ lcd.setCursor(4, 7);
+ lcd.print("COOLANT TEMP");
+ lcd.setCursor(104, 7);
+ lcd.print("DISTANCE");
+ lcd.setCursor(164, 7);
+ lcd.print("INTAKE MAP");
+
+ lcd.setCursor(260, 7);
+ lcd.print("ELAPSED");
+ lcd.setCursor(260, 9);
+ lcd.print("BATTERY");
+
+ lcd.setCursor(0, 14);
+ lcd.print("ACC");
+ lcd.setCursor(122, 14);
+ lcd.print("GYRO");
+ lcd.setCursor(230, 14);
+ lcd.print("MAG");
+
+ lcd.setColor(RGB16_YELLOW);
+ lcd.setCursor(24, 5);
+ lcd.print("rpm");
+ lcd.setCursor(110, 5);
+ lcd.print("km/h");
+ lcd.setCursor(216, 4);
+ lcd.print("%");
+ lcd.setCursor(304, 4);
+ lcd.print("C");
+ lcd.setCursor(64, 11);
+ lcd.print("C");
+ lcd.setCursor(110, 12);
+ lcd.print("km");
+ lcd.setCursor(200, 12);
+ lcd.print("kpa");
+ lcd.setCursor(296, 12);
+ lcd.print("V");
+ lcd.setColor(RGB16_WHITE);
+ }
+ void dataIdleLoop()
+ {
+ // while waiting for response from OBD-II adapter, let's do something here
+ if (state == (STATE_MEMS_READY | STATE_INIT_DONE)) {
+ logMEMSData();
+ }
+ }
+ byte state;
+};
+
+static COBDDevice myOBD;
+
+void setup()
+{
+ lcd.begin();
+ lcd.clear();
+ lcd.setColor(RGB16_YELLOW);
+ lcd.println("Freematics OBD-II Adapter Tester");
+
+ myOBD.begin();
+ myOBD.initSender();
+ myOBD.setup();
+}
+
+void loop()
+{
+ myOBD.loop();
+}
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-22 17:35:41 +0000