1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
|
#include <Arduino.h>
#include <Wire.h>
#include <OBD.h>
#include <I2Cdev.h>
#include <MPU9150.h>
COBDI2C obd;
MPU6050 accelgyro;
void testOut()
{
static const char PROGMEM cmds[][6] = {"ATZ\r", "ATL1\r", "ATRV\r", "0100\r", "010C\r", "0902\r"};
char buf[OBD_RECV_BUF_SIZE];
for (byte i = 0; i < sizeof(cmds) / sizeof(cmds[0]); i++) {
char cmd[6];
memcpy_P(cmd, cmds[i], sizeof(cmd));
Serial.print("Sending ");
Serial.println(cmd);
if (obd.sendCommand(cmd, buf)) {
char *p = strstr(buf, cmd);
if (p)
p += strlen(cmd);
else
p = buf;
while (*p == '\r') p++;
while (*p) {
Serial.write(*p);
if (*p == '\r' && *(p + 1) != '\r')
Serial.write('\n');
p++;
}
} else {
Serial.println("Timeout");
}
delay(500);
}
Serial.println();
}
void readMEMS()
{
int16_t ax, ay, az;
int16_t gx, gy, gz;
int temp;
accelgyro.getMotion6(&ax, &ay, &az, &gx, &gy, &gz);
temp = accelgyro.getTemperature();
// display MEMS data
Serial.print("ACC=");
Serial.print(ax);
Serial.write('/');
Serial.print(ay);
Serial.write('/');
Serial.println(az);
Serial.print("GYRO=");
Serial.print(gx);
Serial.write('/');
Serial.print(gy);
Serial.write('/');
Serial.println(gz);
}
void showECUCap()
{
static const byte PROGMEM pidlist[] = {PID_ENGINE_LOAD, PID_COOLANT_TEMP, PID_RPM, PID_SPEED, PID_TIMING_ADVANCE, PID_INTAKE_TEMP, PID_THROTTLE, PID_FUEL_LEVEL};
for (byte i = 0; i < sizeof(pidlist) / sizeof(pidlist[0]); i++) {
byte pid = pgm_read_byte(pidlist + i);
bool valid = obd.isValidPID(pid);
Serial.print('0');
Serial.print((int)pid | 0x100, HEX);
Serial.print('=');
if (valid) {
int value;
if (obd.read(pid, value)) {
byte n = Serial.println(value);
}
} else {
Serial.println('X');
}
}
}
void setup() {
Serial.begin(115200);
delay(500);
Wire.begin();
accelgyro.initialize();
testOut();
readMEMS();
Serial.println("Init...");
while (!obd.init());
}
void loop() {
showECUCap();
readMEMS();
}
|
