1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
|
/*************************************************************************
* Testing sketch for Freematics OBD-II UART Adapter
* Reads and prints several OBD-II PIDs value
* Distributed under GPL v2.0
* Visit http://freematics.com for more information
* Written by Stanley Huang <stanleyhuangyc@gmail.com>
*************************************************************************/
#include <Arduino.h>
#include <Wire.h>
#include <SoftwareSerial.h>
#include <OBD.h>
// On Arduino Leonardo, Micro, MEGA or DUE, hardware serial can be used for output
// as OBD-II adapter should connect to Serial1, otherwise we use software serial
SoftwareSerial mySerial(A2, A3);
//#define mySerial Serial
COBD obd;
void testOut()
{
static const char cmds[][6] = {"ATZ\r", "ATL1\r", "ATH0\r", "ATRV\r", "0100\r", "010C\r", "0902\r"};
char buf[128];
for (byte i = 0; i < sizeof(cmds) / sizeof(cmds[0]); i++) {
const char *cmd = cmds[i];
mySerial.print("Sending ");
mySerial.println(cmd);
if (obd.sendCommand(cmd, buf, sizeof(buf))) {
char *p = strstr(buf, cmd);
if (p)
p += strlen(cmd);
else
p = buf;
while (*p == '\r') p++;
while (*p) {
mySerial.write(*p);
if (*p == '\r' && *(p + 1) != '\r')
mySerial.write('\n');
p++;
}
} else {
mySerial.println("Timeout");
}
delay(1000);
}
mySerial.println();
}
void readPID()
{
static const byte pidlist[] = {PID_ENGINE_LOAD, PID_COOLANT_TEMP, PID_RPM, PID_SPEED, PID_TIMING_ADVANCE, PID_INTAKE_TEMP, PID_THROTTLE, PID_FUEL_LEVEL};
mySerial.print('[');
mySerial.print(millis());
mySerial.print(']');
for (byte i = 0; i < sizeof(pidlist) / sizeof(pidlist[0]); i++) {
byte pid = pidlist[i];
bool valid = obd.isValidPID(pid);
mySerial.print((int)pid | 0x100, HEX);
mySerial.print('=');
if (valid) {
int value;
if (obd.read(pid, value)) {
mySerial.print(value);
}
}
mySerial.print(' ');
}
mySerial.println();
}
void setup()
{
delay(500);
mySerial.begin(115200);
// this will begin serial
obd.begin();
// send some commands for testing and show response
testOut();
// initialize OBD-II adapter
do {
mySerial.println("Init...");
} while (!obd.init());
char buf[64];
if (obd.getVIN(buf, sizeof(buf))) {
mySerial.print("VIN:");
mySerial.println(buf);
}
delay(1000);
}
void loop()
{
readPID();
}
|
